BLAUBERG AERO - Quiet, durable and versatile bathroom extractor fan with UV-resistant ABS casing
The Blauberg Aero low-noise bathroom extractor fan can be mounted on the wall or on the ceiling and connects to a 100 mm air duct or a ventilation shaft. It is a low-noise axial fan; its sound pressure measured at 3 m is 38 dB(A). It moves up to 102 m³ of air per hour, with a power consumption of 14 W.
The Blauberg Aero 100 H with humidity sensor also switches on by itself when the air is humid, while the Blauberg Aero 100 T with timer starts with the light switch. With its IP34 rating, it can be installed in zone 2 of the bathroom according to IEC 60364-7-701:2019. When the fan is off, the built-in backdraught damper closes the duct, so no air flows back. Our expert staff will help you with sizing and choosing accessories.
Blauberg Aero low-noise bathroom extractor fan in two variants
The Blauberg Aero low-noise bathroom extractor fan can be mounted on the wall or on the ceiling and connects to a 100 mm air duct or a ventilation shaft. It is designed for exhaust ventilation of small to medium-sized premises heated during winter. It is a low-noise axial fan; its sound pressure measured at 3 m is 38 dB(A).
The Blauberg Aero 100 H with humidity sensor also switches on by itself when the air is humid, while the Blauberg Aero 100 T with timer starts with the light switch. After switching off, both keep running for another 2-30 minutes; you can set this time on the timer.
You can choose the variant in the table below; each row links to the page of that variant.
You will find more bathroom and WC fans on the category page. The video shows the installation and wiring steps.
Which variant do you need?
Two variants for 100 mm ducts.
| Variant | When does it switch on? | Turn-off delay | Humidity set point |
|---|---|---|---|
| Aero 100 H, with humidity sensor | with the light switch, or when the humidity rises above the set point | 2-30 min, adjustable | 60-90%, adjustable |
| Aero 100 T, with timer | with the light switch | 2-30 min, adjustable | none |
Both variants have an air flow rate of 102 m³/h, a power consumption of 14 W and a sound pressure of 38 dB(A) measured at 3 m. The difference is in how they switch on.
Why choose this fan?

Low-noise, durable, with backdraught damper
The casing and the impeller are made of UV-resistant plastic, and the motor runs on ball bearings. The bearings are maintenance-free and filled with grease for the whole motor service life. When the fan is off, the built-in backdraught damper closes the duct, so no air flows back. It is also suitable for continuous operation.

Adjustable humidity sensor and timer
You can set the humidity set point between 60 and 90% and the turn-off delay between 2 and 30 minutes. Use the plastic screwdriver supplied for this, because a metal tool may damage the circuit board. The timer board is under mains voltage, so the fan must be completely disconnected from the mains before adjusting.

For the bathroom, also in zone 2
With its IP34 rating, it can be installed in zone 2 of the bathroom according to IEC 60364-7-701:2019. The drawing shows the zones around the bath and the shower. It is protection class II, so it does not need to be earthed.

Wall and ceiling mounting
It offers versatile mounting: on the wall, on the ceiling, in a ventilation shaft or attached to the ducting system. It exhausts the air directly into a ventilation shaft or into a round 100 mm air duct. The pack also contains four screws with dowels and, for the timer variants, a plastic screwdriver.

Easy to clean
The front panel can be removed and washed under running water. The motor needs no maintenance; regular dusting of the impeller and the front panel is enough.
Technical data
| Feature | Value |
|---|---|
| Type | Blauberg Aero 100 H (with humidity sensor and timer), Aero 100 T (with timer) |
| Turn-off delay | 2-30 min, adjustable |
| Humidity set point | 60-90%, adjustable (Aero 100 H) |
| Air duct | Ø 100 mm, round |
| Air flow rate | up to 102 m³/h |
| Power consumption | 14 W |
| Current consumption | 0.085 A |
| Speed | 2 300 rpm |
| Sound pressure | 38 dB(A), in free space, measured at 3 m |
| Supply voltage | 220-240 V, 50 Hz, single-phase |
| Protection class | II (no earthing needed) |
| IP rating | IP34 |
| Ambient temperature | between +1 °C and +40 °C |
| Motor | ball bearings, maintenance-free |
| Backdraught damper | built-in |
| Casing and impeller | UV-resistant plastic, white |
| Weight | 0.56 kg |
The sound pressure is measured in free space at a distance of 3 m. The manufacturer is Blauberg Ventilatoren in Germany.
Dimensions
The letters follow the manufacturer's drawing, dimensions in millimetres.

- □a: outer dimension of the square front panel, 144 mm.
- □b: spacing of the four fixing holes (Ø 4.5 mm), 122 mm.
- c: depth from the front panel to the step of the spigot, 92.5 mm; the end of the spigot extends a further 14 mm.
- Ød: spigot diameter, 100 mm.
- e: thickness of the front panel, 29.5 mm.
| Type | a | b | c | Ød | e | Weight |
|---|---|---|---|---|---|---|
| Aero 100 | 144 | 122 | 92.5 | 100 | 29.5 | 0.56 kg |
The front panel is 144 × 144 mm, and the fixing holes are at the corners of a 122 mm square.
Installation and connection
Requirements of the user's manual.
Installation

- It can be mounted on the wall or on the ceiling.
- It exhausts the air directly into a ventilation shaft or into a round 100 mm air duct.
- If the duct runs through the wall to the outside, it should slope outwards by 1-2°, with a louvre or a rain-protection grille at its outer end.
- Condensate may drip back from a duct running straight up from the fan through the roof, so avoid this routing.
- The direction of the air flow must match the arrow on the casing.
- Do not compress the casing during mounting: a deformed casing may jam the motor and make the fan louder.
- Do not fix it with glue or adhesives; use only screws, as described in the manual.
- If an open-flue gas or other fuel-burning appliance is operating in the home, have a competent person check after installation that no flue gases flow back.
Installation steps

- Cut off the power supply and make sure that the cable is dead.
- Run the power cable to the vent hole.
- Remove the front panel.
- Mark and drill the holes, then fix the fan.
- Connect the fan according to the wiring diagram.
- Refit the front panel.
- Switch the power back on.
Electrical connection
- Installation and connection may only be carried out by a qualified electrician.
- It must be connected to the mains through a disconnecting device with contact separation in all poles that allows full disconnection under overvoltage category III conditions.
- Always disconnect it from the mains before connection, repair and maintenance.
- You will find the wiring diagram on the variant's page and on pages 18-19 of the manual.
Maintenance
Cleaning every six months.
- Clean the fan at least once every six months.
- First disconnect it from the mains and make sure that it is not live.
- Remove the front panel and the decorative panel, and wipe the fan with a dry cloth or a brush.
- Wash the front panel under running water, then wipe it dry.
- Do not allow water or any other liquid to come into contact with electrical components.
- Finally, refit the front panel and switch the power back on.
What is it not suitable for?
Limits of use.
- It must not be installed outdoors and must not be exposed to rain or sun.
- The transported air must not contain dust, sticky substances or fibrous materials.
- It must not be used in an explosive environment, for example near vapours of solvents, gasoline or insecticides.
- Do not cover the intake or the extract vent.
- The ambient temperature may be between +1 °C and +40 °C.
Manufacturer's documents
The English catalogue page shows the performance curve and the dimensions; the user's manual covers installation, wiring and maintenance.
Accessories for installation
For installation we recommend flexible and PVC ducts, a gravity louvre, a rain-protection grille, a clamp and aluminium tape from our online shop, all for 100 mm ducts.

Buy from one of Hungary's most trusted ventilation specialists
Ventilátorház is located at Királyhágó utca 30 in Budapest's XVIII. district. We are a multi-award-winning company with decades of experience. Our expert staff will help you with sizing and choosing accessories. Call them on +36-70-369-9944.
Frequently asked questions
Yes, with its IP34 rating it can be installed in zone 2.
The Aero 100 H has a humidity sensor and a timer, the Aero 100 T only a timer.
Between 2 and 30 minutes; you can set this on the timer.
To a round 100 mm air duct or a ventilation shaft.
Yes, it is built in and closes the duct when the fan is off.
Its sound pressure is 38 dB(A), measured in free space at 3 m.
Yes, the Blauberg VALEO-E 75/100 H centrifugal fan also has a humidity sensor.



